|
|
|||||||
| Z Lounge Off beat topics, PG-13 |
 |
|
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
07-10-2006, 05:47 PM
|
||||
|
||||
|
Buying cutout
Hey guys just curious what's the diameter size of the regular stock exhaust. I'm buying a cutout for my car but I don't want to cut up my catback. So I decided to put it right before the catback system. Does anyone know the size of this piece? I believe it's called the I pipe. I need to know so that I order the right size.
|
|
07-10-2006, 05:49 PM
|
|||
|
|||
|
Stock exhaust size is 2.75". Order a 3" cutout, mine fit perfectly.
__________________
 2000 SS M6 #5445 - 387/384 at the wheels Custom Cam, SLP Lid, Pacesetter LT's/ORY, SLP dual/dual catback, QTP cutout, Hurst w/ WS6 store SS
|
|
07-10-2006, 05:49 PM
|
||||
|
||||
|
Get the 3'' size, the true stock exhaust is slightly smaller than that, but 3" will be the best fit for ya.
__________________
 1994 Patriot Red Z28 A4 / Mods: Flowmaster American Thunder exhaust, Catalytic converter replaced (3in cutout), Moroso CAI, TB bypass, 1LE induction elbow, Hypertech Airfoil ZHawk's Cardomain  SOLD:9/12/2006 -Joey  
|
|
07-10-2006, 05:52 PM
|
||||
|
||||
|
Quote:
|
|
07-10-2006, 06:01 PM
|
|||
|
|||
|
Yes it will fit perfect. I put a cutout on my stock piping.
__________________
2000 SS M6 #5445 - 387/384 at the wheels Custom Cam, SLP Lid, Pacesetter LT's/ORY, SLP dual/dual catback, QTP cutout, Hurst w/ WS6 store SS
|
|
07-10-2006, 06:04 PM
|
||||
|
||||
|
Yes, Dave, 3" it is. That's what I got. =)
__________________
 1998 A4 White Z28- 355 HP/ 346 TQ 13.5 @104mph =D Join the Wolfpack!!|Join NIFBA today! -Uli
|
|
07-10-2006, 07:25 PM
|
|||
|
|||
|
buy a 3" e-cut out.. got mine form DMH
__________________
 2002 Trans Am Engine HP Tuners |Granatelli Lid | K&N Air filter w/Removed Air Silencer | TB Body By-Pass Exhaust (True Duals) STOCK Manifolds | Magnaflow 3" O/R X Pipe | Magnaflow MagnaPacks Mufflers | GMMG Tips Drive Train Pro 5.0 Braking Rotorworks Crossed Drilled And Slotted Rotors | Hawk HPS Pads
|
|
07-10-2006, 09:01 PM
|
||||
|
||||
|
3 inch here too..i took 2 mustang tail pipes and made reducer pipes, but you could prolly just weld it right on to the stock exhuast if you needed.
|
|
08-20-2006, 10:26 PM
|
||||
|
||||
|
sorry to bring up a old topic but where exactly does the cutout go
__________________
|
|
08-20-2006, 10:35 PM
|
||||
|
||||
|
i put mine on the straight pipe after the cat. there's a curve and then a long straight pipe, i put it in the middle.
|
|
08-20-2006, 10:37 PM
|
||||
|
||||
|
ahh how much did it run you to get it installed ?
haha yeah its a nice sig thanks :P
__________________
|
|
08-20-2006, 10:38 PM
|
||||
|
||||
|
The cut-out goes underneath the rear passanger seats in the I-pipe. Ive had mine open for over three years and love it, but Im going with a new exhaust setup so I wont be running my cutout anymore.
|
|
08-20-2006, 10:52 PM
|
||||
|
||||
|
so should i run a 3 inch cut out ?
__________________
|
|
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| About Buying A Car | 86IROCZ | Z Lounge | 12 | 08-02-2006 05:48 PM |
| buying a 96 lt1?? | vatechguy3 | Misc. Tech Support | 2 | 07-23-2006 03:40 PM |
| Cutout Size? | Green95z | Exhaust | 6 | 06-20-2006 02:17 AM |
| Best position for exhaust cutout valve ??!!?? | camarokid95 | Exhaust | 1 | 10-03-2003 01:19 PM |
| Buying Question | rich1223 | Engine Tech | 12 | 09-03-2003 12:30 AM |
Linear Mode
